Installation

 

 

FAQ
Frequently Asked Questions

 

  • When I turn on the switch does it have light?

Yes, all our touch switches have led indicators, turn on the switch red indicator, tur off the switch blue indicator.

 

  • Can I used it with energy-saving lamps or LED lamps?

Yes, our switches can work with energy-saving lamps and LED lamps as long as the wattage is more than 1W.

 

  • What kind of lamps can be fit with your dimmer switch?

Filament lampand dimmable LED lamp; All bulbs  works with mechanical dimmer, works with ours, Only the wattage should be 5-500W.

 

  • Can your switch work with home automation system?

It depends, if the system only needs a signal On / Off, it can be. Otherwise, our with switch is not suitable for home automation system because the codes are different.

 

  • Do you have an intermediate switch?

Yes, our 2 way switch also can be an internedie switch, you can connect three 2 way switches together.

 

  • Which output from the switch - relay or triac?

For On / Off touch switch - relay, dimmer switch - triac.

 

  • Can I install the switch vertically?

Sure, Any Pose.

 

Installation instructions for LIVOLO products.

 

 

Installation instructions for LIVOLO products.     Installation instructions for LIVOLO products.

 

 

Installation instructions for LIVOLO products.

 

Installation instructions for LIVOLO products.

Installation instructions for LIVOLO products.

Installation instructions for LIVOLO products.Installation instructions for LIVOLO products.Installation instructions for LIVOLO products.

 

Installation instructions for LIVOLO products.

 

 

Installation instructions for LIVOLO products.

 

For dimmer switch

 

A = On     B = dim up     C = dim down     D = Off

 

 

Installation instructions for LIVOLO products.Installation instructions for LIVOLO products.Installation instructions for LIVOLO products.

 

Installation instructions for LIVOLO products.

 

Installation instructions for LIVOLO products.

 

Installation instructions for LIVOLO products.

 

Installation instructions for LIVOLO products.

 

Note:

  1. To cancel the synchronization: Repeat the above process, and when you hear two seconds of ‘DI’ during step 3, the synchronization is cancelled successfully.
  2. Please remember the the room number, as different room different button.

 

Installation instructions for LIVOLO products.

 

Note:

  1. If new scene should be add to the scene button (like button ‘II’), repeat the above process.
  2. To cancel the synchronization: Repeat the above process, and when you hear two sounds of ‘DI’ during step 4, it is cancelled successfully.
  3. Please remember the room number, as different room different scene button.

 

 

Attentions

 

Installation instructions for LIVOLO products.

 

 

Installation instructions for LIVOLO products.

 

Resistance touch switch

A resistance switch needs two electrodes to be physically in contact with something electrically conductive (for example a finger) to operate. They work by lowering the resistance between two pieces of metal. It is thus much simpler in construction compared to the capacitance switch. Placing one or two fingers across the plates achieves a turn on or closed state. Removing the finger(s) from the metal pieces turns the device off.

One implementation of a resistance touch switch would be two Darlington-paired transistors where the base of the first transistor is connected to one of the electrodes.

Also, an N-Channel, enhancement-mode, metal oxide field effect transistor can be used. Its gate can be connected to one of the electrodes and the other electrode through a resistance to a positive voltage.

 

Piezo touch switch

Piezo touch switches are based on mechanical bending of piezo ceramic, typically constructed directly behind a surface. This solution enables touch interfaces with any kind of material. Another characteristic of piezo is that it can function as actuator as well. Current commercial solutions construct the piezo in such way that touching with approximately 1.5 N is enough, even for stiff materials like stainless steel.

 

Capacitance switch

A capacitance switch needs only one electrode to function. The electrode can be placed behind a non-conductive panel such as wood, glass, or plastic. The switch works using body capacitance, a property of the human body that gives it great electrical characteristics. The lamp keeps charging and discharging its metal exterior to detect changes in capacitance. When a person touches it, it increases the capacitance and triggers the switch. It fits for LIVOLO.

MODERN

ENERGY SAVING

VERSATILE

SAFE